Xantrex-technology GPIB-M-XT Manual de usuario Pagina 10
- Pagina / 134
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
About This Manual
viii Operating Manual for Multichannel Functionality (GPIB-M)
Appendix B SCPI Command Reference Describes the Standard Commands
for Programmable Instruments (SCPI) commands supported by various products
with the Multichannel Interface installed.
Appendix C Error Messages Describes the error messages that could appear
during operation.
Appendix D Calibration Provides the calibration procedures and parameters.
Manual Revisions
The current release of this manual is listed below. Updates may be issued as an
addendum.
Release 2.1 (2003-04)
Power Supply Safety Markings
Alternating Current Off (Supply)
Earth (Ground) Terminal On (Supply)
Protective Conductor Terminal
Caution (Check manual for
additional information.)
- Internal GPIB-M Interface: 1
- Multichannel Functionality 1
- Power Supplies 1
- Warranty 4
- Release 2.1 iii 5
- Disclaimer Product 6
- Xantrex Technology, Inc 7
- 8999 Nelson Way 7
- Burnaby, British Columbia 7
- Canada V5A 4B5 7
- About This Manual 9
- Manual Revisions 10
- Power Supply Safety Markings 10
- Table of Contents 11
- Section 4. Status Registers 12
- Section 5. Current Sharing 13
- Appendix A. GPIB 13
- List of Tables 15
- List of Figures 17
- Release 2.1 17 19
- Features and Specifications 20
- Features and Functions 20
- Specifications 21
- Release 2.1 21 23
- Release 2.1 23 25
- Release 2.1 25 27
- (XFR 1200 Watt model shown) 28
- Initial Inspection 29
- GPIB CANBUS USER LINES 30
- CANBUS GPIBUSER LINES 30
- USER LINES 31
- Basic Setup Procedure 33
- Release 2.1 33 35
- Configure for GPIB Operation 36
- Release 2.1 35 37
- Table 2.2 CANbus Pins 38
- Release 2.1 37 39
- Connection 39
- • on power up, and 40
- Release 2.1 39 41
- User Lines 42
- J7 User Cable 43
- Ferrite Block 43
- Section 3. Operation 45
- Operation 46
- Power Supply Operating States 46
- Power Supply Regulation Modes 47
- • Constant Voltage (CV) 47
- • Constant Current (CC) 47
- Remote Control Modes 48
- Front Panel LEDs 49
- Power Supply Operation 50
- Release 2.1 49 51
- Release 2.1 57 59
- Auto Sequencing 62
- Editing the Sequence 63
- Setting Sequence Repetitions 64
- Selecting a Trigger Source 64
- Editing Step Parameters 64
- Deleting Steps 64
- Deleting Sequences 65
- Select Sequence to Run 65
- Querying the number of steps 65
- Skipping a Step 66
- Querying Operation 66
- Status Registers 72
- Overview 72
- REGulating 74
- Sub-Register 74
- Release 2.1 73 75
- Release 2.1 77 79
- Release 2.1 79 81
- Status Register Commands 83
- Clear Status Command 84
- Parallel Poll Enable Register 85
- Status Byte 85
- Power-on Status Clear 86
- Individual Status Query 86
- Operation Complete 86
- Wait-to-Continue Command 86
- • No sharing 92
- Current Sharing 94
- Protocol Specifications 96
- Electrical Specifications 97
- Mechanical Specifications 97
- Performance Specifications 97
- Release 2.1 97 99
- SCPI Command Reference 100
- Understanding SCPI Commands 101
- Using Minimum and Maximum 102
- Terminating Characters 103
- Common Commands 103
- Using Queries 103
- Boolean Parameters 104
- Discrete Parameters 104
- Numeric Parameters 104
- String Parameters 104
- SCPI Command Summary 105
- Table B.1IEEE 488.2 Commands 106
- Table B.2Readback Commands 107
- Table B.9System Commands 110
- Table B.10Status Commands 111
- Table B.11Protection Commands 114
- Table B.12User Lines 114
- Table B.13Output State 114
- Expressions 117
- Appendix C. Error Messages 119
- Command Error List 120
- Execution Error List 120
- Release 2.1 119 121
- Device-Specific Error List 122
- Query Error List 123
- User Request Event 123
- Operation Complete Event 123
- Front Panel Error Codes 124
- CPU Error Codes 124
- Auto Sequencing Error Codes 124
- CANbus Error Codes 125
- Multichannel Error Codes 125
- Current Share Error Codes 126
- Appendix D. Calibration 127
- Setup and Equipment 128
- • 6 digit DVM 128
- • current shunt 128
- • variable load 128
- Calibration Procedure 129
- Calibration 130
- Exit calibration mode 131
- Restore Factory Calibration 131
- PRINTED IN CANADA 134
Relacionado con productos y manuales para Herramientas Xantrex-technology GPIB-M-XT
(136 paginas)
(73 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales